Difference between revisions of "pulseaudio virtual sinks"
From thelinuxwiki
(Created page with "below is a post found to stream music over skype. this can also be used to stream over teamspeak(tested). taken from [http://askubuntu.com/questions/257992/how-can-i-use-pul...") |
|||
| Line 1: | Line 1: | ||
below is a post found to stream music over skype. this can also be used to stream over teamspeak(tested). | below is a post found to stream music over skype. this can also be used to stream over teamspeak(tested). | ||
| − | taken from [http://askubuntu.com/questions/257992/how-can-i-use-pulseaudio-virtual-audio-streams-to-play-music-over-skype] | + | taken from [http://askubuntu.com/questions/257992/how-can-i-use-pulseaudio-virtual-audio-streams-to-play-music-over-skype] |
| + | |||
| + | [http://www.freedesktop.org/wiki/Software/PulseAudio/Documentation/User/Modules/#index63h3 pulseaudio module documentation] | ||
After many hours of tinkering I finally achieved it! | After many hours of tinkering I finally achieved it! | ||
Revision as of 17:40, 8 March 2015
below is a post found to stream music over skype. this can also be used to stream over teamspeak(tested).
taken from [1]
pulseaudio module documentation
After many hours of tinkering I finally achieved it!
I created two Null Outputs and created two loopbacks for the first and one loopback for the second.
pactl load-module module-null-sink sink_name=Virtual1 pactl load-module module-null-sink sink_name=Virtual2 pactl load-module module-loopback sink=Virtual1 pactl load-module module-loopback sink=Virtual1 pactl load-module module-loopback sink=Virtual2
Next I opened PulseAudio Volume Control (pavucontrol)
These are my settings. I typed them in the order they appear. Numbers go from up to down.
Recording tab:
Applications:
All applications should input from your headset/microphone.
Except the application(s) you want to send the audio to should be set to one of the following. If you ONLY want to send the audio: Monitor of Null Output 1. It will be the first "Null Output" in the list. If you want to send both the audio and your voice: Monitor of Null Output 2. It will be the second "Null Output" in the list.
Virtual Streams:
Loopback to Null Output (1): Your headset/microphone
Loopback to your headset/microphone: Null Output 1. It will be the first "Null Output" in the list.
Loopback to Null Output: Null Output 1. It will be the first "Null Output" in the list.
Playback tab:
Applications:
All applications should output to your headset/speaker.
Except the application(s) you want to record/send through Skype/stream should be set to Null Output 1. It will be the first "Null Output" in the list.
Virtual streams:
Loopback of your headset: Null Output 2. It will be the second "Null Output" in the list.
Loopback of Monitor of Null Output (1): Your headset.
Loopback of Monitor of Null Output (2): Null Output 2. It will be the second "Null Output" in the list.
just to not get confused with the "null Output", just specify the names like this:
pactl load-module module-null-sink sink_name=Virtual1 sink_properties=device.description="NAME HERE (mic+music)" pactl load-module module-null-sink sink_name=Virtual2 sink_properties=device.description="NAME HERE (only music)" pactl load-module module-loopback sink=Virtual1 pactl load-module module-loopback sink=Virtual1 pactl load-module module-loopback sink=Virtual2
[[category:pulseaudio]
